Browse all practice questions for the Omaha Plumbing Code Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Omaha Plumbing Code Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • When installing a horizontal soil line, a clothes washer branch connection may not be connected closer than _____________ feet downstream from a water closet opening.
  • All tubing used for tail pieces in commercial installations shall be _____________ gauge brass.
  • What is the bond amount a master plumber must pay to operate a business?
  • Enzymatic grease interceptors are categorized as what?
  • Which of the following scenarios requires the installation of a backflow prevention device?
  • The maximum spout height of a handicapped accessible drinking fountain is ___________ ?
  • Water heater relief valves shall be piped ____________________________________.
  • A pan shall be provided for all floor drains when it is installed ________________.
  • A shower room with multi-shower heads shall be serviced by a minimum 3-inch drain for each how many valves or heads?
  • Street fittings may be used on which material?
  • What is the fixture unit rating for a typical utility sink?
  • What is the maximum net square footage allowed to install a unisex restroom?
  • Sanitary sewer lines shall be labeled with what type of labels and letters?
  • What is the minimum diameter for the inspection pipe over both the inlet and outlet of a septic tank?
  • The knee clearance required for a handicapped accessible drinking fountain is a minimum of __________ inches from the floor to the cantilever.
  • When installing 3 inch floor drains in a building level below grade, one drain must be installed for each how many square feet or fraction thereof?
  • When a lead flashing for a vent stack is used the minimum weight per square foot of the lead is ______________ pounds?
  • A water closet in an establishment serving liquor is rated as ______________ waste fixture units.
  • If a change of direction in a horizontal plane of a building sewer is made with two 45 bends, a cleanout is not necessary if the bends are how many feet apart or more?
  • Which interceptor should all commercial garage drains connect to?
  • When a backwater valve is installed in a subsoil drain system, it is required to be in a minimum diameter manhole of how many inches?
  • Which type of backflow preventer is most commonly used in irrigation systems?
  • What is the minimum waste pipe size for a shower?
  • The inlet pipe of a grease interceptor shall extend to how many inches below the liquid level?
  • A 3 inch p-trap shall have a maximum depth of ____________ inches for the trap seal.
  • A vertical rainwater leader installed inside the building is not required to have a cleanout if _______________________.
  • For what type of systems can the plumbing board adopt regulations?
  • The relief vent in a multi-story building shall be what size?
  • What is the minimum vent size for two water closets installed back to back?
  • What is the minimum clear floor space required in front of a handicapped accessible water closet?
  • When installing plastic pipe underground, the maximum distance between supports that secure the pipe to the bottom of the trench shall be __________ feet.
  • Slip joint compression type waste line connections shall ______________________.
  • When measuring the maximum height of a testable backflow device you measure to the _________________________________.
  • How high above the flood rim of a fixture must a vent be extended vertically before it can be run horizontal?
  • How is the waste system for a grease interceptor vented?
  • Which of the following conditions is prohibited for discharging residential subsoil drainage systems?
  • What must be the configuration of a stack vent when extended above the first floor to receive plumbing fixture discharges?
  • What is the maximum width for any septic system absorption trench?
  • What is the maximum number of two-inch floor drains allowed on two-inch horizontal waste?
  • Where roof drains are required, overflow drains must be ___________________________.
  • What is the recommended maximum distance between cleanouts for a 4-inch diameter pipe?
  • What does the term 'grade' refer to in plumbing?
  • A water closet in an establishment serving liquor is rated as how many waste units?
  • What is the primary function of a vent in a plumbing system?
  • Hot water shall be connected to which side of the fixture?
  • A ___________________ cannot be used to wet vent a water closet?
  • How many members make up the plumbing board?
  • At what height is a RPZ typically mounted for optimal performance?
  • All wells shall be protected by an RPZ except when used for __________________.
  • __________________________ is the maximum allowable length of a 2 inch horizontal waste arm from the combination wye and 1/8 bend fitting to the fixture connection before a revent is required?
  • The elevation difference between the invert of the inlet pipe and the invert of the outlet pipe of a septic tank should be how many inches?
  • What is the standard height above finished floor for a cleanout in a stack?
  • What is the maximum height of a flush valve handle for a handicapped accessible water closet from the finished floor?
  • For which type of plumbing connections is a double check valve typically used?
  • _______________________ is the correct mounting height for a RPZ?
  • Which of the following shall not be installed in a new commercial kitchen?
  • A two-way cleanout is not required for a dwelling if the developed length between the first cleanout and the city main is _____________ feet or less.
  • Which of the following fixtures' final waste connection cannot be connected by the use of a compression gasket?
  • _________________________ is the minimum size for a residential garage drain?
  • For which of the following is a bond NOT typically required in the plumbing field?
  • What is the maximum slope of a battery vented soil or waste branch?
  • A manhole is required when installing a rainwater leader on ____________ inch or larger pipe.
  • What is the minimum required depth for a mop sink?
  • What is the minimum depth requirement for a floor sink?
  • What is the maximum number of side by side clothes washers allowed on a 4 inch horizontal waste?
  • What is required for the installation of a dishwasher in terms of its waste piping?
  • When a subsoil drain system is connected by gravity to a storm sewer, it shall connect through a?
  • Grease interceptors cannot be made from which material?
  • Supplies to ice machines and coffee, tea or chocolate dispensers shall be provided with what type of connection from a minimum 1/2 inch rigid water pipe?
  • A residential dishwasher not connected to a kitchen sink has a fixture unit rating of _______________.
  • On new construction a drain is required to be located no more than _______ feet from a RPZ assembly.
  • _______________ is the minimum clear floor space for a handicapped accessible wall or post water fountain or cooler.
  • Which plumbing fixture necessitates having an independent isolation valve?
  • The seal of every fixture trap in a plumbing system shall be protected by a ____________________________.
  • Who appoints the members of the plumbing board?
  • ______________________ is the minimum discharge pipe size from a sump or receiving tank for a sewage pump system?
  • Type K or L soft copper is permissible when placed __________________ in a partition on remodel only.
  • For building storm drains that require a manhole, the manhole must be how far or less from the building?
  • Which of the following is not used as a scald prevention device?
  • The use of dielectric unions is prohibited on which of the following?
  • A shower waste shall run independent of other fixtures directly to a _______ inch or larger waste.
  • The seal of every fixture trap in a plumbing system shall be protected by a __________________________.
  • Which member of the plumbing board is a non-voting member?
  • The minimum height knee clearance under a sink for ADA is _______ inches above finish floor.
  • A partition is required between which of the following?
  • After an applicant has taken their journeyman test for the fourth and fifth time, how many days must they wait to retest?
  • _____________ is the minimum depth of a trap seal in inches?
  • A commercial disposal with a three inch trap has a fixture unit rating of __________?
  • What is the minimum allowed thickness of the concrete installed to encase a trench drain?
  • How many members of the plumbing board constitute a quorum for business transactions?
  • In a plumbing business, how must the vehicles display the license holder's name?
  • How many years of apprenticeship are required before an individual can test for their journeyman test?
  • In which location should drinking fountains or water coolers not be installed?
  • What action is required if an applicant fails the journeyman test after their fourth attempt?
  • At what temperature must hot water heaters be set to prevent growth of Legionella bacteria?
  • The outlet pipe in a grease interceptor must originate within how many inches of the tank bottom?
  • When extending a branch soil line to the first floor for a water closet and lavatory, what is the maximum vertical rise allowed?
  • In new construction, a floor drain or floor sink must be located within how many feet of a water heater?
  • What is the maximum number of 2 inch floor drains allowed on a 2 inch horizontal waste?
  • A vent stack or vent opening shall be located within how many feet developed length from a future fixture opening in a commercial building?
  • What should a subsoil drain system connect through when linked by gravity to a storm sewer?
  • In a plumbing system, when is indirect drainage required?
  • What authority does the plumbing board have regarding rules and regulations?
  • Where can a pressure vacuum breaker be installed within a building?
  • What is the minimum vent pipe size from a sump or receiving tank for a sewage pump system?
  • Non-potable water may be used for which of the following applications?
  • According to the plumbing code, what is the primary purpose of requiring a bond for master plumbers?
  • In the Omaha Plumbing Code, "interconnection" is interchangeable with what other term?
  • All Durham soil and waste systems are required to be of which drainage type?
  • A grease interceptor is required for establishments serving food when the fixture count exceeds how many units?
  • ______________________ is the minimum trap size for a bidet?
  • If a type I interceptor is 18 feet from the point of connection to the building drain, ___________ is the minimum size vent required?
  • What is the minimum required clear space in front of a lavatory?
  • A shampoo sink in a beauty shop has a fixture unit rating of ___________.
  • What are the potential consequences for a business that fails to display the required licensing on their vehicles?
  • Cleanouts for pipes larger than 2 inches require how much horizontal space?
  • Chemical and soap dispensing equipment shall be connected to an independent ____________________________.
  • What is the minimum required clearance in front of a floor urinal?
  • The fixture load of a 4 inch branch interval is based on _______________ per inch per foot fall.
  • ____________ is the minimum trap seal for a shower?
  • What is the minimum thickness of a closet floor flange allowed?
  • What is the maximum vertical distance from the fixture outlet to the trap weir?
  • Which type of material is not acceptable for use in underground waste and vent systems?
  • An owner’s responsibility for grease interceptors includes what?
  • Trench drains used in chemical or corrosive conditions shall be made of ___________________.
  • A shampoo sink in a beauty shop has a fixture unit rating of ______________.
  • When is it permissible to install a circulation pump for a whirlpool tub below the fixture trap?
  • When installing no-hub couplings underground the no-hub coupling shall have a minimum of ________________ bands.
  • What is the required connection type for water heater relief valves?
  • A sump pump located in an elevator pit shall discharge?
  • What material should trench drains used in corrosive environments be made of?
  • How many fixtures can be discharged onto a stack above a stack vented water closet?
  • The distance between cleanouts on a 2-inch horizontal waste line shall not exceed _________ feet.
  • What is the required distance for a pressure vacuum breaker to be installed above any connected fixtures?
  • What is the minimum required depth of a mop sink?
  • Which of the following is not used as an anti-scald device?
  • What is the minimum size measurement inside of a shower stall?
  • When a 4 by 1-1/2 inch sanitary cross is used to connect two like fixtures, which of the following is required?
  • Cleanouts in waste pipes two inches and smaller shall have at least ____________ inches of horizontal space in front of the cleanout?
  • What is the minimum clearance required above the finished floor for a handicapped water closet?
  • What should be ensured regarding waste drains for commercial dishwashers?
  • When installing plastic waste piping below grade there must be a minimum __________________ clearance around the entire outer circumference of the pipe or fitting when penetrating concrete.
  • A backwater valve installed in a manhole more than 2 feet deep requires the diameter of the manhole to be at least _____________ inches?
  • A two-way cleanout is unnecessary if the building drain is extended to a manhole that is how many feet away or less from the building?
  • Which of the following materials may not be used to secure a closet flange to the floor?
  • How far apart must two drinking fountains be to be rated as two fixtures?
  • A no-hub reducing coupling may be used in the _______________ position?
  • When is a business required to allow the public access to the restrooms?
  • ___________________ is the minimum size plastic soil or waste pipe that may be installed underground?
  • A sump that receives the waste from a single floor drain does not require ______________________________________.
  • All below grade water supplies, one inch and smaller in size, shall be type K copper ______________________________________.
  • The minimum size waste line for a floor sink is __________________.
  • On a handicapped accessible wall or post mounted cantilever type water fountain, the minimum clearance for knee space from finish floor to cantilever shall be ___________ inches.
  • Which of the following guidelines pertains to the installation of a drinking fountain?
  • What is the minimum allowed slope of the bottom of a trench drain?
  • Wash fountains have a fixture unit rating of ____________________________.
  • The discharge temperature for a Type IV interceptor should be limited to what maximum value?
  • When passing through a wood stud, PVC plastic pipe shall be protected from puncture by a minimum _______ inch thick steel plate.
  • What is the maximum height of a handicapped accessible lavatory from the finished floor to the rim?
  • A transition coupling may be used to ______________________________________________.
  • What is the least dimension required for a accessible lavatory?
  • What is the minimum required clearance in front of a water closet?
  • A roof measuring 40 feet by 20 feet with a vertical wall on one side measuring 4 feet by 40 feet, _________________________ must be added to the roof area to determine minimum roof drain square feet?
  • The maximum slope of a battery vented soil or waste branch is _____________ inch per foot.
  • A mop sink faucet shall be mounted a minimum of _____________ inches above the finished floor.
  • What is the minimum height for the flow of water on an ADA drinking fountain?
  • On a horizontal branch, what is the maximum distance from the fixture opening that a vent can be connected?
  • A potable well will not be allowed to be cross-connected with the water supply from MUD under which condition?
  • If a vent stack terminates 4 feet from a ventilation grill, what must be done?
  • Handicapped accessible water closets height is measured from the finished floor to the top of the __________________.
  • Which of the following is the correct waste fixture unit rating for a typical sink in a residence?
  • Which method is not acceptable for indirectly venting a waste?
  • When may a grease trap be installed?
  • If a stack penetrates the roof 7 feet from a firewall, what must be done?
  • A rolled and grooved copper potable water piping system may be installed ___________________________.
  • Which one of the following traps are legal?
  • Clear floor space dimensions on a handicapped accessible urinal shall be ________ by ________ inches.
  • A drain should always have a slope to ensure proper flow. What is the minimum slope recommended?
  • Vertical cross-linked Polyethylene pipe shall be supported separately at intervals not to exceed _______________.
  • What is the minimum height of the lettering on restroom doors indicating men's and women's?
  • What is the minimum slope for a 10" horizontal waste line?
  • Which of the following statements is true regarding the discharge of water heater relief valves?
  • A handicapped accessible lavatory shall have ________ by _________ inches clear floor space minimum.
  • For piping larger than two inches in diameter, at least ___________ inches of horizontal service space shall be provided in front of the cleanout.
  • What is the common method for sealing piped connections in plumbing?
  • A handicapped accessible urinal shall have its flush controls mounted no more than _____________ inches above the finish floor.
  • Which of the following describes an air break?
  • What is the minimum combined area, in square feet, of a mop sink?
  • What is the minimum diameter required for a shower waste pipe?
  • What is the maximum slope allowed for a sanitary drainage pipe?
  • What is the maximum allowable spacing between cleanouts in a drainage system?
  • At what minimum height above finished floor should a cleanout be installed above a water closet?
  • Which type of urinal does not have an integral trap?
  • The minimum space above the test ports of a backflow assembly is _________________.
  • What rating does a toilet usually have in commercial settings?
  • A pump and motor on a whirlpool tub shall be ___________________ from the access opening.
  • What is the required bond amount that all members of the plumbing board shall provide?
  • What is the purpose of a fixture unit rating?
  • Slip joint compression type waste line connections shall be:
  • When a bypass is installed around a RPZ _______________________ is required?
  • Which of the following criteria do not apply to a 4-inch running trap?
  • Cross-linked polyethylene (PEX) pipe may be used in sizes __________________.
  • A service sink with a three inch trap standard would have a fixture unit rating of ________________________.
  • What is the minimum height of a shower head above the shower floor?
  • What is the bond amount required for plumbing contractors according to community guidelines?
  • On building storm drains requiring a manhole, the manhole shall be installed within _____________ feet of the building.
  • All water services 1 through 1 1/4 inches shall be type ________________ copper.
  • What is the minimum distance between two water closets, center to center?
  • All new commercial kitchen grease interceptors must be connected to which?
  • What is the minimum capacity of a septic tank for a residence with 2 bedrooms or less?
  • Which of these fixtures requires an overflow?
  • What is the minimum capacity of a septic tank for a dwelling with over five bedrooms?
  • What is the minimum required distance from the center of a water closet to the center of a urinal?
  • What material should trench drains used in chemical or corrosive conditions be manufactured from?
  • The rim or counter surface shall be no higher than ________ inches above the finished floor on a handicapped accessible lavatory.
  • What is the maximum spout height allowed for a handicapped accessible drinking fountain?
  • A 3" vertical stack without a water pipe shall be in what type of wall?
  • When can an individual first apply to take the journeyman test?
  • What is the function of a dual check valve in plumbing systems?
  • Combination wye and eighth bends can be used in which configurations?
  • A pedestal urinal has a fixture unit rating of _______________.
  • What must be clearly visible on the vehicles of plumbing businesses?
  • A transition coupling may be used to _________________________________________________.
  • Water heater relief valve discharge lines shall not _________________________________.
  • Which is not a requirement for a flushometer?
  • How many 4 inch vent stacks would be required for a 6 inch building drain?
  • When passing through a wood stud, PVC plastic pipe shall be protected from puncture by a minimum __________ inch thick steel plate.
  • What defines a cross connection under the Omaha Plumbing Code?
  • For a building with (4) six inch roof drains connected to an 8 inch main, what size vent is required?
  • All residential garage drains shall be _____________ drains.
  • All spills occurring during pumping or maintenance of grease interceptors must be reported within how many hours?
  • All commercial garage drains shall be a minimum size of _______ inches.
  • In plumbing installations, what is the purpose of an isolation valve?
  • Which of the following is crucial for the installation of a sewage pump system?
  • What is the valve control area height for a handicapped accessible shower, measured in inches above the finished floor?
  • What is the minimum liquid depth for a type III interceptor?
  • What is the minimum waste pipe size for a floor sink?
  • If a urinal protrudes from the wall more than 20 inches, what is the maximum height for the flush controls?
  • Which factor is NOT considered when determining the bond amount for a plumbing business?
  • What is the maximum number of clothes washers allowed on a three inch stack?
  • What is the minimum allowed distance from the finished floor to the center of the tee serving a clothes washer?
  • Regardless of pipe size, cleanouts shall be installed in such a manner as to provide at least ____________ inches of vertical service space?
  • What is the minimum depth required for knee clearance?
  • What is the minimum letter height required for the name on both sides of a vehicle used by a business or company?
  • What must the combined area of the openings through a floor drain cover be equal to or greater than?
  • The distance from the finished floor to the center of a handicapped accessible urinal must be a maximum of __________ inches.
  • Pipe and valve identification is required on above floor commercial piping systems in buildings that exceed how many floors in height?
  • What is the maximum height from the rim of a wall mounted urinal to the floor?
  • Installation of a pressure vacuum breaker inside a building ____________.
  • What is the minimum allowable length of a non-handicapped accessible stall or compartment for a water closet?
  • Two-way cleanouts are not required on building storm drains if the storm drain drains to daylight how far from the building?
  • What is the minimum space allowed between the edge of a lavatory and a wall?
  • How often must all grease interceptors be pumped according to the code?
  • If a 2 inch area drain is connected to a properly vented sanitary building drain, what is the maximum distance allowed between the building drain and the trap before a vent is required?
  • When can you use a PVC "waste and overflow" on a bathtub in an apartment building?
  • How many inches must be allowed for minimum floor turn around space in an ADA restroom?
  • How high above the flood rim of a fixture must a vent be extended vertically before it can be run horizontal?
  • When is it appropriate to connect a water heater using a flexible connector?
  • In plumbing, at what distance should venting for a drain generally occur?
  • Stud guards for piping passing within one and one half inch of the edge of the stud should be made from which material?
  • How many inches is the required clearance in front of a pedestal urinal?
  • All laundry boxes installed in fire partitions shall be what?
  • What is the minimum diameter of openings for accessing the chambers of a grease interceptor?
  • What is the minimum width of a stall of a non-handicapped water closet?
  • The maximum discharge temperature for a Type IV interceptor is set at what degree?
  • What feature is required in the installation of cleanouts regardless of the pipe size?
  • ____________________ is the minimum clear floor space required in front of a handicapped accessible lavatory?
  • A by-pass line shall be installed around water meters ___________ inches and larger.
  • The maximum rim height of a handicapped accessible urinal is __________ inches from the floor.
  • What is the maximum height for shower controls in an ADA shower?
  • What is the minimum width of the clear space for a handicapped accessible water fountain or cooler?
  • Trenches running parallel to a footing shall not extend below what angle to the bearing plane of the footing?
  • The minimum size concrete pad for a two-way cleanout on a building sewer shall be ______________________>.
  • Which backflow preventer is not suitable for continuous pressure situations?
  • On a horizontal waste branch of how many feet or less in length may the fixture outlet be termed a cleanout?
  • Sway bracing and blocking must be installed on all horizontal sanitary and storm drainage piping of which size or larger?
  • What is the minimum inside diameter for a manhole used for a cleanout with more than one inlet?
  • What is prohibited when installing water heater relief valve discharge lines?
  • The heal inlet of a "heal inlet one-quarter bend" shall be installed only in which position?
  • How is the term "plumbing" defined according to the code's guidelines?
  • A pressure vacuum breaker must be installed a minimum of how many inches above the highest point of usage?
  • What is the maximum number of times an applicant can take the journeyman test before they must wait to retest?
  • What is the minimum height requirement for the lettering on restroom doors indicating "Men's" or "Women's"?
  • What is the minimum distance from the narrow side of the water closet to the side of the urinal in a restroom for single use?
  • What is the purpose of a relief vent in plumbing systems?
  • What is the minimum required waste pipe size for a trench drain that is 8 feet long?
  • What is the range for the distance of an ADA water closet from the wall or partition?
  • On which side of the toilet must the flush controls of an ADA water closet be located?
  • The waste from a garbage can washer shall drain into a _________________________.
  • Which of the following cannot be used for backflow protection in a high hazard?
  • How many years of experience must a master plumber or journeyman plumber have before joining the plumbing board?
  • A shower room having 8 multiple-shower valves shall be serviced by a minimum _________ inch drain.
  • __________________ is the minimum trap seal on a Type I interceptor?
  • What is a possible consequence of discharging from a subsoil drain?
  • The outlet pipe in a grease interceptor shall originate within ____________ of the tank bottom.
  • What should be the focus when installing an interceptor?
  • When making a lead and oakum joint on bell and spigot pipe, the minimum depth of the lead in the joint shall be ____________.
  • What is the maximum allowable length for flexible water supplies for plumbing fixtures unless special circumstances occur?
  • What is required for all plumbing board members in compliance with Nebraska State Statute?
  • What is the minimum discharge pipe size from a sump or receiving tank for a sewage pump system?
  • Cleanouts must be installed on building sewers at intervals not to exceed how many feet?
  • How should the waste from a single rack commercial type dishwasher be piped?
  • How many fixtures may be installed or connected to a single grease trap?
  • If an applicant fails their journeyman test, when can they retest?
  • The jurisdiction that this chapter shall be enforced in extends to the corporate limits plus what extra territorial zone?
  • Why is maintaining venting in a sewage pump system important?
  • What is the correct terminology for a plumbing fixture intended to connect to a drainage system?
  • When making a lead and oakum joint on a bell and spigot pipe, the minimum depth of the lead in the joint shall be ___________________.
  • The minimum required depth of a floor sink is __________________.
  • The minimum required slope for a horizontal vent line is _______________.
  • Which type of valve is essential for connection to a shower stall?
  • Who is responsible for the construction specifications for inspection manholes installed for grease interceptors?
  • When a scupper is used as an overflow drain it shall be ___________________________.
  • The minimum rated flow capacity for a grease trap is ______________________.
  • What is the minimum allowed thickness of the concrete installed to encase a trench drain?
  • The vent from a pneumatic ejector system shall be _____________________.
  • What is the minimum size service opening for a whirlpool tub?
  • What is the minimum distance above the flood level of a fixture for an approved air gap?
  • When a grease interceptor is abandoned, which of the following is not required?
  • How many inches from the side of a urinal to any wall or partition minimum?
  • What is the minimum size floor drain allowed in a veterinary clinic?
  • What is the maximum number of back to back clothes washers allowed on a 4 inch horizontal drain?
  • Which of the following areas can the plumbing board set regulations for?
  • When is it acceptable to install grease traps?
  • In a business that sells food or drinks, what is the minimum slope to the floor drain in a public restroom?
  • The minimum clear floor space for a handicapped accessible wall or post water fountain or cooler shall be _________ by __________ inches.
  • A handicapped accessible water closet shall be ___________ inches from the wall to the center of the water closet.
  • What is the minimum size of access opening required for a backwater valve installed less than 24 inches deep inside a building?
  • Flow control devices for grease traps shall be installed on the ______________.
  • To install maintain and repair testable backflow assemblies as a journeyman you are required to be certified through classes approved by ______________________.
  • What is one of the owner's responsibilities for grease interceptors?
  • On a 4 inch mop sink waste that is extended 38 feet from its connection on a horizontal main, what is the minimum size vent required?
  • The maximum allowed distance from the finished floor to the center of the tee serving a clothes washer is ______________.
  • A relief vent is required when there are ___________________ or more branch intervals?
  • What is the minimum clearance required for a flushometer from the bottom of the grab bar in an ADA stall?
  • What is the minimum capacity of a grease interceptor according to the code?
  • How often must a master plumber renew their business bond?
  • The removable shower strainer shall have a minimum diameter of ________ inches.
  • What is the minimum waste opening on a laundry sink?
  • Which backflow protection method cannot be used in a high hazard scenario?
  • What is the minimum waste pipe size for a Type I interceptor?
  • When is it permissible to connect a storm drain to a sanitary sewer?
  • If two lavatories are installed back to back in an 8 1/2 inch wall _________________.
  • ____________________ is the minimum vent pipe size from a sump or receiving tank for a sewage pump system?
  • The height of a handicapped accessible lavatory must not exceed ___________ inches.
  • What is the maximum number of water closets with a fixture rating of 3 that would be allowed on a 4-inch building drain laid at a slope of 1/4 inch per foot?
  • Shower rooms having more than two shower stalls shall provide a __________ near the stalls.
  • What is the minimum waste pipe size for a residential food waste grinder?
  • A water closet in a retail establishment has a fixture unit rating of ________________.
  • The combined area of the openings through a floor drain cover must be equal to, or greater than what?
  • Non-potable water lines shall be labeled with ___________ labels and ______________ letters.
  • When using lead as a flashing on a roof drain, the flashing shall extend at least ____________________ inches beyond the outer circumference of the stone guard clamping ring.
  • What is the maximum number of water closets with a fixture rating of 4 fu allowed on a 4 inch building drain with a 1/4 inch slope?
  • All commercial garage drains shall connect to a _____________ interceptor.
  • What is the maximum number of side-by-side clothes washers on a 4-inch horizontal waste line?
  • A wall hung commercial single carrier back to back shall require a chase with a minimum inside clear space of how much?
  • An indirect waste must discharge into another fixture at what specific point?
  • The term used in the Omaha Plumbing Code to describe the fall of the invert of a sewer is known as what?
  • At what minimum distance must a sewer line be installed from a water line?
  • When is it allowed to connect a water heater using flexible connections?
  • The maximum height of the flush valve handle shall not exceed ________ inches for a handicapped accessible water closet.
  • The distance between cleanouts on horizontal waste lines larger than 2 inches shall not exceed _____________.
  • The purpose of an interceptor is to remove which of the following?
  • What is the key purpose of the plumbing board's regulations?
  • A two inch threaded plastic fitting ______________________________.
  • How many days is a person given to correct a violation if convicted of prohibited plumbing work?
  • A water meter shall be installed in the __________________________ position.
  • The highest fixture connected to a waste or soil stack not requiring a re-vent is said to be _____________________.
  • What is the maximum number of water closets allowed on a 3 inch stack in a single family dwelling?
  • In a vent situation, how should a heal inlet of a one quarter bend be installed?
  • Which of the following materials is typically used for water service lines?
  • What is the maximum amount of fixtures allowed on a single battery vent?
  • What material is specified for dishwasher waste pumped below the floor?
  • How much clear space is required above a water closet?
  • Clothes washers in a group of three or more have an individual fixture unit rating of __________________________________.
  • When approved manholes are installed instead of cleanouts, what is the maximum distance allowed between manholes?
  • What is the minimum clear floor space in front of a shower opening?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy